Plastering under a fur coat with your own hands

Plastering beneath a fur coat is a special method that gives walls character and texture. It’s a well-liked option for people looking to give their house a traditional or rustic feel. In order to give walls a distinctive and tactile finish, a thick layer of plaster is applied and then textured to resemble a fur coat.

You can accomplish this effect yourself if you have the appropriate equipment and supplies. Although it takes some time and patience to get the hang of, the results are well worth the effort. Plastering under a fur coat can be a rewarding do-it-yourself project, whether you’re starting from scratch or updating an old wall.

This post will walk you through the process of successfully applying a fur coat over plaster with your own hands, giving your walls a distinctive and long-lasting finish that will look great in any room.

Choosing a composition

Plaster beneath a fur coat is something you can make yourself or purchase already constructed.

The first, more cost-effective option uses water, sand, and cement to prepare the solution. Gypsum is an alternative to cement that can be used. The mineral mixture does have some disadvantages, though: the gypsum coating absorbs water and is not appropriate for exterior decoration, and the cement plaster "fur coat" is inelastic, resulting in cracks.

Pre-made compositions are an additional choice. They can be fully prepared for use, or they can be dry and need to be diluted with water before use. Dry mixtures are preferred by builders because they are less expensive, weigh less, and are easier to transport to the repair site.

The silicone plaster is delivered fully assembled and ready to use. It’s simpler to work with—even someone who isn’t an expert can manage it. Polymer compositions are elastic, long-lasting, and suitable for nearly any surface (from plasterboard to brick). They also don’t break after drying. Although they are more expensive, the polymer plaster coating that underlies a fur coat is long-lasting and resistant to moisture.

Advantages and disadvantages

Although plaster under a fur coat is not a novel technique, it is still widely used for interior or exterior decoration due to its many noteworthy benefits:

• low price for materials and tools;
• the ability to do all the work yourself;
• increase in heat and sound insulation (provided that the finished coating layer is thick enough);
• possibility of repeated painting;
• aesthetic appearance of finished surfaces.

• Quick contamination: dust and dirt accumulate on the relief surface, and it is difficult to clean it.
• Short-lived (in case of using cheap cement mixtures).

Application area

The purpose of the "fur coat" plaster is to finish the following decoratively:

• facades of houses;
• rooms;
• basement;
• fences;
• niches, columns, bas-reliefs.

The decorative coating can be applied to plasterboard, concrete, or brick surfaces, depending on the type.

Preparation of the base

DIY Surface preparation is the first step in fur coat plastering. The wall needs to have all objects attached to it removed, as well as any dust and dirt. The old finishing material should be taken off, especially if it is not firmly attached.

A sharp tool, like a chisel, is used to make notches on the composition so that it sticks to the wall firmly.

Next, proceed with priming. Application of the solution is done with a wide brush or roller. It is preferable to use a sprayer on extremely uneven surfaces to ensure that the liquid gets into all of the nooks and crannies.

Apply the "fur coat" plaster after the primer has dried completely.

Preparing the solution

You will need a binder and a filler if you want to create the composition yourself. The latter can be made of clay, gypsum, cement, or lime. Sand is the most readily available filler. Pre-sifting unalloyed medium-fraction is the better option.

The following is how to prepare "fur coat" plaster for DIY projects:

1. one part of cement and three parts of sand are combined;
2. the resulting mixture is poured into a mixing container;
3. for each kg of dry matter, take 200 ml of water;
4. mix thoroughly with an electric drill with a special attachment or a construction mixer;
5. hold for 5 minutes, mix again.

The end product ought to resemble a lump of sour cream. Avoid overly thickening the solution as this will increase consumption and make application inconvenient.

Materials and tools

You’ll require:

• a container for mixing;
• an electric drill or a construction mixer;
• sandpaper (fine-grained);
• brushes and boards;
• tinting paste;
• a building rule;
• a textured roller and spatula;
• a stick and a broom.

You can use a specialized machine designed for fur coat plaster application for a speedy and superior result. This apparatus consists of a rotating container filled with flexible metal plates. The "organ" sprays the solution onto the wall when the handle is turned.

Application methods

Fur coat plaster can be applied in multiple ways. The area to be treated, the desired texture, and your experience are taken into consideration when selecting one that is suitable.

Broom

The materials needed for this method are minimal. It is only recommended to process small surfaces with a birch stick and broom because manually spraying the solution takes a long time.

1. The broom is dipped into a container with the solution, the composition is collected on it.
2. Take a stick in one hand, placing it parallel to the surface being treated.
3. Hit the broom on the stick so that the splashes fly onto the wall.
4. Repeat all operations until the wall is covered with an even layer of the composition.

Fur coat plaster is applied with a stick and broom, a laborious procedure that is rarely used because it is hard to get an even layer the first time.

Brush

Fur coat plaster can also be applied outdatedly with a brush and board. It works well for finishing both inside and outside.

After dipping the brush into a container containing the solution, it is brought to the wall, turned over so that the bristles are facing upward, and then pulled from the wall in your direction using a board. Splashes from this will land on the wall and cover it.

Roller

Using a roller for application is the best option for novice finishers. This only requires a roller, a rule, and a spatula; no other tools are required. A uniform first layer will not be difficult to achieve, and the work proceeds quickly.

Using a spatula, gather the solution and spread it across the surface. Level the layer with a rule. Use a roller to smooth the plaster that has been applied to the wall. Work fast, until the solution is completely dry.

If the work is being done indoors and a fine texture is required, sandpaper the plaster after it has dried.

Compressor

Applying the "fur coat" plaster with a hand sprayer or a compressor will allow you to finish the job the quickest. The final coating will have a uniform layer of solution and be of excellent quality.

Compressors will aid in achieving the appropriate texture as well as expediting the process: to produce a fine texture, add a liquid solution to the apparatus, and to produce a coarse texture, prepare a thick mixture.

Grid

Using a finely mesh, you can apply plaster underneath a fur coat; this is also a simple technique. Using a trowel, the solution is applied to the prepared surface while the mesh is pressed against it. Once completed, the mesh is carefully peeled off, leaving the plaster in place and maintaining the relief texture of the wall.

Step	Description
1. Surface Preparation	Clean the wall, remove loose material, and apply a primer to ensure proper adhesion.
2. Mixing Plaster	Mix the plaster to a consistent, thick paste, following the manufacturer"s instructions.
3. Applying the Base Layer	Use a trowel to spread the first layer of plaster evenly on the wall, maintaining a rough texture.
4. Creating the Fur Coat Texture	While the base layer is still wet, use a broom or brush to create a textured pattern resembling a fur coat.
5. Curing and Drying	Allow the plaster to dry slowly, avoiding direct sunlight and strong drafts, to prevent cracking.
6. Finishing Touches	Once dry, inspect for any imperfections and touch up as needed.

Under a fur coat, plastering is a great way to give your walls durability and texture. With a little perseverance and the appropriate equipment, anyone can master this technique. The uneven surface serves to conceal wall flaws in addition to giving the piece a pleasing appearance.

You don’t need expensive equipment or specialized skills to achieve a professional-looking finish if you follow the right procedure. The secret is to properly prepare the surface and use even, consistent strokes to apply the plaster.

You can give your walls a distinctive, textured surface that gives character to any space by following the indicated steps. It’s a satisfying project that can improve your home’s appearance and make you feel proud of yourself.

Plastering beneath a fur coat is a useful and ornamental method that enables you to manually apply a textured, long-lasting finish to walls. This technique adds a distinct character to any surface, making it both aesthetically pleasing and doable for do-it-yourself enthusiasts.

Video on the topic

How to make plaster under a fur coat

Plaster (fur coat) for beginners! (100% method)

How to apply a side fur coat to the facade, decorative plaster with your own hands.

Plastering the facade with a compressor. Mechanized fur coat plaster